V1.01 A Digital Parts Library For The 74HCxxx Devices. ----------------------------------------------- This new library should you help you using real world standard digital parts in LTSPICE. The library can be extended easily by other parts of this family and it can be also adapted to other logic families like 74HCT,AC,ACT,LVT and so on. More than forty parts are already included and the library will grow. All the files are in the Yahho group's file section. Files->Lib->Digital 74HCxxx I have added a folder "others" in this directory nad I would be happy if other people contribute models there. I will then include them into the "big" library. Helmut Sennewald The A Devices ------------- LTSPICE contains already A devices for logic simulations. A description about these devices can be found in the help pages. Help->LTSPICE->Circuit Elements A special functions Syntax: Annn n001 n002 n003 n001 n004 n005 n006 n007 n008 [parameters] The node n008 is the reference level of the A device and it is assumed to be 0 if no net is connected. You can specify the low and high level of such an A device, but there is no connection for a supply voltage. Be aware that any pin of an A device connected to 0(ground) is treated like nothing is connected. If you want 0V on an A device, you need a net with value 0V which is not node 0. The New 74HC Devices -------------------- The intention was to implement a library for real digital devices like the 74HCxx series. These new library parts will offer additional features compared to the A devices. * Floating supply voltage, therefore parts are split into input section, logical core and output section. * Two sets of symbols, standard and IEC symbols * Parameter passing on device basis * Delay modifier as an instance parameter * Supply voltage dependant delay and other characteristics All models have been divided into three sections. >--| INPUT-Translator |----| 1V-LOGIC A devices |----| OUTPUT Driver |--> The input level converter is one central subcircuit for a device family as well as the output drivers are only a few different types like normal drive, buffer and tristate driver. They are made with E , B.sources and the SW switch SPICE component. The input and ouput sections don't use clamp diodes at the moment, because this makes the simulation slower. If you have a need for that, just enable the lines with the diodes in the input and output section of the 74HC.LIB file. Therefore you have to remove the * at the beginning of all these lines in the subcircuits of the receivers and drivers. *D1 0 in DIO1 -> D1 0 in DIO1 *D2 in VCC DIO1 -> D2 in VCC DIO1 *D1 0 out DIO2 -> D1 0 out DIO2 *D2 out VCC DIO2 -> D2 out VCC DIO2 This small, but in some cases necessary feature, can increase the simulation time up to 70%. Installation ------------ Copy/extract the file 74hc.zip into the LTSPICE directory "...\sym\Digital". It creates automatically a new folder 74hc. Copy the file "74hc.lib" into the LTSPICE directory "...\sub". That's it. Every schematic using thes parts must then have a command line .INCLUDE 74hc.lib. If you want to use the waveform formatter part, then copy "dview10.asy" and "dview5.asy" into the directory "...\sym\Digital". The corresponding library file "dview.lib" should be copied to the LTSPICE directory "...\sub". The necessary command line in the schematic will be .INCLUDE dview.lib. An Example Circuit ------------------ Let's take a look to an example of an 74HC08 AND gate. First add the command line .INCLUDE 74HC.LIB to your schematic. This modelfile 74HC.LIB can be placed either in the working directoty or in the LTSPICE directory C:\Programme\Ltc\SwCADIII\lib\sub. Now place the 74HC08 on your schematic. Right click on the instance to set the VCC and GND net names according to your supply voltage net names. The already set default is the name VCC for the positive supply voltage and net 0 for ground. If you have a net +5V instead, then change VCC to +5V. Do the same with net name 0 for your circuit ground. Right click again to set some parameter values. The HC-family devices have a supply voltage dependant charcteristic. The parameter VCC=5 tells the model this value, here 5V. The simulated characteristic is according to the typical parameters at 25 degree from the data sheet. If you want more maximum delay, then set the factor SPEED=1 to a higher level, e.g. SPEED=2.0. If you set it to 0.5, then you have nearly the speed of ACMOS devices. Don't forget to place a DC source supplying the VCC net on your schematic. That's all what is specific to the new library. There are two special parts for better waveform viewing in the dview.lib file. These are used with the symbols dview5.asy and dview10.asy. They add an offset and gain to each signal so that the signals are sperated vertically on the output window. There is an example (example.asc) file with some of the new parts in the YAHOO group's folder Files->Lib->sch->Digital 74HCxxx . Best you try first this example. If it runs, then your environment has been setup correctly. Simualation of digital devices in (LT)SPICE can become very time consuming. A fast PC is very important here. The Subcircuit Definition in the Symbol Editor ---------------------------------------------- Right click with the mouse on the symbol to see the properties. SpiceModel VCC 0 SpecLine VCC=5 SPEED=1 TRIPDTV=1e-9 What it means: VCC 0 +supply NET is VCC, default -supply NET is 0(GND) VCC=5 5V supply voltage, used to calculate delays SPEED=1 Delay multiplier of 1 TRIPDTV=1e-9 LTSPICE internal timestep for A elements BY THE WAY; this "SpiceModel" line uses a nice trick to add two pins(nodes) to a part without using the "Add PIN" in the symbol editor. This the only chance to have supply nets as "parameters" in the schematic instances. The Subcircuit Definition in the netlist ---------------------------------------- U20 ___ a----------| & |______y b----------|___| 74HC08 The netlist: XU20 a b y VCC 0 74HC00 VCC=5 SPEED=1.0 TRIPDT=1e-9 | | | | | | | | | | 1 2 3 4 5 6 7 8 9 10 1 The subcircuit instance name 2 Net name of one input 3 Net name of one input 4 Net name of output y 5 Net name of the supply voltage VCC, can be any other net name 6 Net name of the ground of the 74HC08, here 0 but can be on any net 7 The model name 74HC08 8 Value of the supply voltage, used to calculate voltage dependant parameters 9 Delay multiplier, the normal delay is multiplie by this factor 10 TRIPDT is a simulation time step parameter for any A device, let it 1e-9 One user reported a convergence problem with a CD4049 oscillator circuit. This problem could be solved in different ways. Chance 1: Use the alternate solver: Control Panel->SPICE Solver-Alternate Chance 2: Reduce the value Gmin in the SPICE control panel: Control Panel->SPICE Gmin 1e-11 Chance 3: Use the .TRAN ..... startup command instead of .TRAN ... . It hasn't helped in this case, but in some other cases.